Give Us A Call: (800) 872-3684

NCF 2000 Negative Air Machine

$875.00
In stock
SKU
AM2000

The NCF2000 Negative Air Machines are designed for indoor use and provide the most efficient air filtration with three stages of filtration. The final stage includes a HEPA (High-Efficiency Particulate Air) filter that can remove 99.97% of particles 0.3 micron or larger from the air. For portability, each unit is equipped with four handles and four rolling casters. The two speed motor is thermally protected and powers the three stage filtration process. The units are independently tested and backed by a one year limited warranty.

Three Stages of Filtration

First Stage - Pre-filter Pad

  • 24" x 24" x 1" - 1-Ply Pad
  • Removes large particles up to 10 microns and larger from the air flowing through the unit, thereby preventing premature loading of the second stage and HEPA filters. The pre-filter pad is recommended to be changed as it becomes loaded and the airflow capacity of the unit decreases—or the pressure gauge at the control panel exceeds 2.6 inches at high speed or 1.9 inches at low speed, of W.C.

Second Stage - Ring Panel

  • 24” x 24” x 1” — 2-Ply Ring Panel
  • Removes particles up to 1 micron and larger from the air flowing through the unit, thereby protecting the more expensive, HEPA filter. The ring panel filter is recommended to be changed as it becomes loaded and the airflow capacity of the unit decreases—or the pressure gauge at the control panel exceeds 2.6 inches on high speed (1.9 inches on low speed) of W.C.

Third Stage - HEPA

  • 24” x 24” x 11.5” — (99.97%) Wood Frame HEPA Filter
  • Removes smaller contaminated particles up to 0.3 microns from the air flowing through the unit and has an efficiency rating of 99.97%. The HEPA filter is recommended to be changed as it becomes loaded, the airflow capacity of the unit decreases, and the pressure gauge at the control panel exceeds 2.6 inches on high speed (1.9 inches on low speed) of W.C.

Specifications

  • Housing: galvanized steel
  • Power : 115 volts, 60 Hz, 1625 rpm
  • Motors: 1.0 HP (9 amps)
  • Exhaust: 12" diameter
More Information
Brand NC Filtration
Motor 1.0 HP (9 amps)
Exhaust Port 12 Inch
Voltage 115V
Frequency 60hz
Construction Galvanized Steel
Write Your Own Review
Write a ReviewNCF 2000 Negative Air Machine

⚠ CAUTION ⚠

DO NOT OPERATE THE UNIT WITHOUT THE HEPA FILTER INSTALLED! OPERATING WITHOUT THE HEPA FILTER INSTALLED OR USING NON-APPROVED POWER CORDS MAY CAUSE DAMAGE TO THE ELECTRICAL SYSTEM AND/OR MECHANICAL COMPONENTS. FAILURE TO COMPLY WILL VOID THE WARRANTY.

 

ELECTRICAL REQUIREMENTS

The unit requires a minimum of 115 V, 60 Hz, 9.5 amp, power supply for normal operation. The unit requires an industrial grade 12/3 cord, in good condition. Do not use a damaged cord. The cord should be properly grounded (ground pin on the plug) and the continuous length should not exceed 50 feet for proper operation. Do not expose the unit or power cord to water.

 

Unit Set Up & Start Up

  • The unit is to be operated away from doorways or other make-up air sources. Properly set up the exhaust and seal off any opening. Do not exhaust into
    uncontaminated or occupied areas.

 

  • Before powering the unit on:
    • lock the two rolling casters to keep the machine in place
    • confirm the rocker switch is in the off position
    • plug in the power supply cord
  • To start the machine, select the speed by pressing the top for high and
    the bottom for low.
To Top