Foster® 40-50™ Interior Defense™ Mold Resistant Coating

$350.00
In stock
SKU
CHE4050

Foster® 40-50™ Mold Resistant Coating is specially formulated with select EPA-registered, antimicrobial agents to provide long-term protection against odor-causing bacteria, mold and mildew growth on its surface.

Features

  • A tough, water-resistant coating for use in areas prone to mold growth.
  • Specially formulated with select EPA-registered, antimicrobial agents to provide long-term protection against odor-causing bacteria, mold and mildew growth on its surface.
  • Ideal for use in attic spaces, wall cavities, crawl spaces, floor joists or wherever mold remediation has occurred.
  • Can be used over a variety of surfaces such as wood studs, OSB, plywood, painted surfaces, wall board, masonry and metal.
  • Applied at a coverage rate of 300 sq. ft./gallon for fast drying and low odor application.
  • Low viscosity and good body allows for easy application with most airless spray equipment, brush or roller.
  • Water-based formulation for non-hazardous application and use when applied according to instructions.
  • Can be used for industrial, commercial, residential, hospital and school applications.

Foster® INTERIOR DEFENSE™ Mold Resistant Coating 40-50 meets the requirements of:

• MAS Certified Green®

• California Dept. of Public Health Standard Method v1.2

• VOC Emissions and Content requirements to contribute to LEED v4 EQ Credit: Low Emitting Materials – Paints and Coatings

• Collaborative for High Performance Schools EQ 7.1

VOC Content: 38 g/l, less water and exempt solvents.

More Information
Brand Foster
Chemical Type Encapsulant
Coating Mold
Dilution Ready-to-Use
Packed As Pail
Container Type 5 gallons
Write Your Own Review
Write a ReviewFoster® 40-50™ Interior Defense™ Mold Resistant Coating

Material And Surface Preparation

Stir well. DO NOT THIN. Apply only to clean, dry surfaces. Ensure that all surfaces are free of all wax, grease, oil, dirt, rust, mold and other surface contaminants. Following complete cleaning procedures, sanitize the entire surface with Foster® 40-80 First Defense™ Disinfectant, following manufacturer’s directions. Patch any large voids or defects. On painted surfaces, remove all flaking, loose or chalking material. Sand all glossy painted surfaces using 220-grit sandpaper to roughen the entire area. All rusted, metal surfaces must be primed before application. Although Foster® Interior Defense™ (40-50) may be applied directly onto cleaned, unrusted, galvanized surfaces, it is recommended that these surfaces be primed.

Application

Apply Interior Defense™ to all surfaces at a rate of 250 – 400 sq. ft./gal. (6.1 – 9.8 m2 /l) to create a uniform film on the surface. Spraying or brushing will give the smoothest finish. For optimum performance, maintain uniform recommended coverage. Porous or uneven surfaces will require more material.

Spray equipment:

Interior Defense™ can be applied with virtually any type of airless spray equipment on the market today. Reversible cleaning 0.015” – 0.017” spray tips are recommended for optimum application. The average viscosity range is 2,500 – 8,000 cps.

Important:

When applying Interior Defense™, proper personal protective equipment must be used. Necessary equipment and clothing are the same as would be used when applying other water-based paints or coatings. Ensure that the application area is well-ventilated during application to avoid buildup of vapors. Appropriate respiratory protection must be used when applying by airless spray. Use of a respirator with organic vapor cartridges is suggested if adequate ventilation cannot be achieved. After application of Interior Defense™, continue to ventilate the area with fresh, dry air to ensure proper drying of the coating and to exhaust odors. Ventilation should be continued until the odor is reduced to an acceptable level for building occupants.

Clean Up

Use fresh water to clean equipment before product dries. Dry product may be removed with undiluted pine oil or citrus-based cleaners or with nonflammable chlorinated solvents

Attachments

To Top