Product added to cart
$939.75
In stock
SKU
TT0055-5in
Novatek’s 5″ Air Dust-Free Grinders is the choice for your toughest challenges. Grind steel or concrete with virtually no dust.
The 5" & 7" Shrouded Right Angle Grinders are ready to tackle your toughest grinding surface preparation needs. Whether you're grinding coatings for spot cleaning or feathering for re-coating, our grinders can handle the challenge with dust free ease.
Novatek's Shrouded Right Angle Grinders utilize a 3M™ brand Coating Removal Discs or CRD®. The advantage of this non-woven, open wed disc is that it will remove residual coatings or impacted corrosion into the substrate after coatings removal with the Shrouded Needle Scalers or PPT, but will not destroy the surface profile produced by these tools. In accordance with SSPC surface specifications, it may be necessary to utilize more than one type of cleaning device to achieve SP-11 power tool cleaning to bare metal.
Features & Benefits
- Heavy Duty Motor - The 1.2HP Pneumatic and 120volt, 8.0Amp Electric Motors maintain speed under load to maximize coating removal.
- Power Source - Single power source for PPT and Grinders standardizes all replacement bearings, vanes etc.
- Note: PPT’s rotational speed is 2300-3000 RPM Grinders rotational speed is 5500 RPM
- Floating Shrouds - A flexible shroud with a 360º radial vacuum take-off ensures even air flow and maximum capture of dust & debris. The floating shrouds can even utilize a full range of abrasives to tackle your toughest grinding needs.
Brand | Novatek |
---|---|
Surface Prep Tool Type | Right Angle Grinder |
Current | 8 Amp |
Voltage | 120V |
Working Width | 5 Inch |
Power | 1.2 Hp |
RPM | 5500 |
Features | 360 Degree Radial Vacuum, Dust-free |
Write Your Own Review
Placing Tool in Service
- Always install, operate, inspect and maintain this product in accordance with all applicable standards and regulations (local, state, country, federal, etc.).
- Compressed air models always use clean, dry air at 90 psi (6.2bar/620kPa) maximum air pressure at the inlet. Higher pressure may result in hazardous situations including excessive speed, rupture, or incorrect output torque or force.
- Electric models must always utilize proper gauge, and rated electrical cords with correct connections.
- Be sure all hoses and fittings are the correctly sized and secured.
- Ensure an accessible emergency shut off has been installed in the air or electrical supply line. Make others aware of its location.
- Do not use damaged, frayed, or deteriorated air hoses and fittings.
- Always use proper gauge electrical cords with correct connections. (When applicable.)
- Electric models must not use damaged, frayed, or deteriorated electrical cords and connections.
- Keep clear of whipping air hoses. Shut off the compressed air before approaching a whipping hose.
- Always turn off and disconnect the tool from its power supply before installing, removing or adjusting any accessory, or before performing
any maintenance on the tool. - Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel. Use only recommended lubricants.
- Keep work area clean, uncluttered, ventilated and illuminated.
- Keep all electrical connections clear of water or other liquids. (When applicable.)
- Do not operate the machine while flammable or volatile liquids such as gasoline, diesel or jet fuel are present. Failure to do so can result in
explosion. (When applicable.) - Do not remove any labels. Replace any damaged label.
Using The Tool
- Always wear protection when operating or performing maintenance on this tool.
- Always wear hearing protection when operating this tool.
- Always use Personal Protective Equipment appropriate to the tool used and material worked. This may include dust mask or other breathing apparatus, safety glasses, ear plugs, gloves, apron, safety shoes, hard hat and other equipment,
- Prevent exposure and breathing of harmful dust
and particles created by power tool use: - Some dust created by power sanding, sawing, and grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
- - Lead from lead based paints, Crystalline silica from bricks and cement and other masonry products, and Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
- Keep others a safe distance from your work area, or ensure they use appropriate Personal Protective Equipment.
- This tool is not designed for working in explosive environments, including those caused by fumes and dust, or near flammable materials.
Read all instructions and data in operation and maintenance manual prior to operation of this equipment.
These instructions are for your protection and convenience. Please read them carefully since failure to follow the precautions could result in injury. Whenever using electric powered equipment, basic safety precautions should be followed.
Before Use
Inspect he tool’s external parts, fittings and assemblies for loose or damaged parts prior to use.
CAUTION: DO NOT inspect the tool without first disconnecting it from the power supply!
In Use
- Always use the correct abrasive discs.
- Experimentation with various disc materials and abrasive materials may be beneficial in terms of productions.
- The electric motor switch should be in the “off” position when not in use.
- After proper power has been supplied the switch should be turned to the “on” position.
- The drive motor is capable of various rotational speeds. To determine optimal rotational speeds, refer to the instructions provided with the abrasives.
- No attempt should be made to increase or decrease the grinders rotational speed setting recommended for each individual abrasive. Always follow manufacturer’s recommendations. Failure to do so could result in premature wear of failure of the abrasive disc.
- If the tool produces unusual sounds or vibrates excessively, shut down immediately for repair or return for factory inspection.
- Exposure to excessive vibrations or repetitive work practices may be harmful. The use of gloves will help damped vibrations during prolong use.
- Due to fire hazards, do not use gasoline or volatile thinners to flush or clean the tool in any way.
- Maintenance and repair records should be kept on all grinders.
- Frequency and nature of repair may reveal unsafe operational conditions.
More from Novatek