Product added to cart
Pullman Holt 1HP, 5 Gal HEPA Vac.
$1,044.75
Out of stock
SKU
VP1086
Pullman Holt model 86ASB5D4C
The model 86ASB5D4C is designed to work in tight areas, on scaffolding or any job site where a rugged steel compact vacuum is required. Easy to carry and transport.
The model 86ASB5D4C is designed to work in tight areas, on scaffolding or any job site where a rugged steel compact vacuum is required. A compact all-steel HEPA wet/dry vacuums that are small and lightweight enough to be easily carried or transported, yet rugged enough to handle the toughest jobsites. Designed to work in congested, tight areas. These vacuums are also excellent tools in many maintenance and shop environments for fast, convenient pick-up of hazardous materials.
Features
- Air seal gasket between the motorhead and tanks forms a positive lock fit.
- Heavy gauge steel tank with powder coated finish.
- High efficiency 'Drop-in' style HEPA filter individually certified to have a minimum efficiency of 99.97% at .3 microns (based on 1EST-RP-CC007 particle count test method).
- A Dacron filter bag covers the entire spacer sleeve and HEPA filter for three-stage filtration; Dacron material sheds dust to maintain maximum vacuum efficiency
- Includes complete set of tools.
- 25 ft. power cord.
- 5 Gallon
- 1 HP
Tool kit includes
- 10 ft. x 1.5 in.crushproof hose
- 5 ft. two-piece metal wand
- ABS floor brush tool
- ABS floor squeegee tool (not included with 86ASB5D4C)
- Round dusting brush
- Crevice tool
Specifications
- 86ASB5D4C Style: Dry
- Horsepower: 1
- Waterlift: 85"
- CFM: 96
- Recovery: .75bu / 5 gallon
- Shipping Weight: 42 lbs.
- Product Code: B160419
| Brand | Pullman-Holt |
|---|---|
| Air Filtration Tool Type | HEPA Vacuum |
| Motor | 1 Hp |
| Water Lift | 85 Inch |
| CFM | 96 |
| Recovery | 75bu / 5 gallon |
| Recovery Tank Capacity | 5 gal |
| Hose Diameter | 1.5 Inch |
| Cord Length | 25 Feet |
Grounding Instructions
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having equipment grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This appliance is for use on a nominal 120- Volt circuit.
Vacuum Assembly Guide
Note: No lubrication is required. Service of electrical parts must be performed by an authorized service representative.
Disposable Bag Changing:
Over filling the bag will result in loss of vacuum efficiency. The recommended bag replacement procedure is as follows:
- Remove vacuum head and HEPA filter.
- Tape a 6 mil poly bag over the canister so that the canister is completely enclosed.
- Using the poly bag as a glove,disengage the paper bag from the vacuum inlet stem inside the canister.
- Invert the canister so that the paper bag falls into the poly bag. Seal the poly bag and dispose as prescribed by law.
- Attach a new paper bag to the vacuum inlet securely and fold the top of the bag down so it does not interfere with the HEPA filter.
- Replace the HEPA filter and motor head.
- Thoroughly vacuum the work area to recover any asbestos dust which may have been dropped.
Storage
Store in a dry location indoors. Wrap the cord carefully around the vacuum head to avoid accidental damage.
Filter Care and Maintenance
- The primary filter (paper bag) is completely sealed and cannot be reused (dry units only). When the bag is filled to the point where vacuum efficiency is reduced, it must be replaced with a new one. Remove the filled paper bag, place in the specially marked plastic bag and dispose of properly. Reinstall a new primary filter (paper bag) as stated in “Filter Installation”. Do not operate vacuum cleaner for dry pick-up without the primary filter (paper bag) installed.
- The pre-filter is attached to the lower face of the HEPA filter with a velcro strip. Should this filter become visibly dirty or clogged, replace it. Place the used filter in a specially marked bag, seal and dispose of properly.
- The final or HEPA filter is a sealed unit and cannot be cleaned. Periodically make a visual inspection of this filter for excessive amounts of debris. If the filter appears to be clogged,has a hole, or has changed color (should be white), indicating excessive dirt build-up, replace with a new filter, making sure to install new secondary and primary filters. Place the used filter in the specially marked plastic bag, seal and dispose of properly.
Write Your Own Review
Related Products
