Product added to cart
Spray Foam 12oz.
$57.75
In stock
SKU
MS0170
Quick Cure Foam Sealant foam is a high performance, 1-component, sealant ideal for quickly filling gaps and voids to block out air drafts, moisture, and insects.
- Available in 12 oz.
Touch ‘n Seal Quick Cure foams are high performance, single component, moisture curing, Class 1 fire retardant, expanding polyurethane sealants. Use Quick Cure Polyurethane Foam Sealants to permanently air seal and insulate gaps and cracks to block drafts, moisture and insects while improving comfort and reducing energy usage in commercial, industrial, agricultural and residential applications. Common applications include sealing around plumbing, ventilation outlets, electrical junctions, between sill plates and concrete slabs, or anywhere requiring a fast, economical air-sealing moisture barrier. Quick Cure foams work on wood, masonry, insulating foam boards, metal, wire insulation, plastics and sheetrock and are available in both straw dispensed aerosol cans and larger cylinders with hoses and applicators.
Quick Cure Straw Foam
A fast and easy, high-yield means to seal cracks and gaps. Patented all-direction dispensing easily maneuvers tight spots. Reusable dispensing means you can restart the can later.
Features & Benefits
- Available in 12 oz. cans
- 12 oz. Yield (¼" bead) - 900 linear feet
- 24 oz. Yield (¼" bead) - 1,900 linear feet
- Density - 1.75+/-.25 lbs./cu.ft.
- R Value - 4.9 per inch thickness
- Max. Service Temp for Cured Foam - 240ºF (116ºC)
- Shelf Life - 18 months
- Class A Fire Resistance
- Flame Spread - 10
- Smoke Developed - 15
- ICC-ES ESR-1926 approved
- Tack-Free Dry Time - <30 minutes
- Full Cure Time - 24 hours
MS0170 Spray Foam 12oz. 12 cans/case
| Brand | DAP |
|---|---|
| Chemical Type | Foamer |
| Dilution | Ready-to-Use |
| Packed As | Case |
| Container Type | 12 cans |
Write Your Own Review
Directions:
Important – read all directions and cautions before use. Always wear gloves, eye protection and work clothes. Use drop cloths. Product is flammable during dispensing – turn off sources of ignition prior to use. Always refer to local building codes prior to application of Touch ‘n Seal sealants. CAN MAY BURST IF LEFT IN HOT VEHICLE, EXPOSED TO DIRECT SUNLIGHT OR TEMPERATURES ABOVE 122°F (50°C).
Preparation:
To promote adhesion, surface must be clean, dry, and free of all foreign material. Assemble straw and adapter, then carefully screw the trigger assembly onto valve. With trigger assembly attached, shake well for 30 seconds. Holding the can upside-down, slowly activate trigger until foam begins to dispense. Important: Before starting the job, first practice dispensing onto scrap materials.
Application:
For best results this product should only be dispensed in the UPSIDE-DOWN position and apply in spaces with 40% greater relative humidity. Fill gap no more than 1/3 full, allowing room for expansion. Do not overfill. Important: Foam will continue to dispense for a few seconds after releasing the trigger – keep the straw tip moving to reduce the possibility of overfilling. Foam is tack-free in 30 minutes and dries in 4 hours. Excess foam can be trimmed, sanded, caulked or plastered as necessary. Direct sunlight discolors foam if not painted or covered.
Clean-up:
If wet foam contacts skin, clean immediately with a dry rag – do not use water – water accelerates curing. Cured foam must be removed mechanically from surfaces. Uncured foam can be cleaned from most surfaces with Foam Cleaner or acetone. If foam dries on skin, apply generous amounts of petroleum jelly, put on plastic gloves and wait 1 hour. With a clean cloth, firmly wipe off residue and repeat process if necessary. DO NOT use acetone or other solvents to remove product from skin.
Storage/Re-Use:
Stop & restart up to 3 weeks later. To store unused portion, bend straw back onto the knob atop the dispensing trigger. Store can upright below 90° F (33°C). Product can be reused within three weeks if stored properly. To re-use, cut the end of the straw (removing any cured foam), shake well and apply as directed.